产品中心新网站资料
产品中心新网站资料

产品中心新网站资料

1801, 9103 high thermal conductivity adhesive

FS-1801 Single component high thermal conductivity adhesive This product is a high temperature curing……

Related
message
detail
content details

FS-1801 Single component high thermal conductivity adhesive

This product is a high temperature curing single component high thermal conductivity adhesive, the product has good thixotropy and storage stability before curing, no precipitation separation phenomenon. Easy to use, short curing time, high bonding strength, excellent thermal conductivity, widely used in all kinds of electronic components and heat dissipation modules, this product is suitable for automatic dispensing equipment, but also manual scraping.

Product characteristics
1.
This product has good thermal conductivity, low shrinkage and low water absorption.
2.
This product has good resistance to cold and heat shock after curing and has passed a number of environmental tests.
3.
This product exhibits adhesion to metal materials.
4.
In the curing process, this product has good reactivity and non-vertical flow.

Curing condition
Curing time 160×30 min
Usage method
1.
This product needs to be stored in cold storage (3 months at 5 ° C), please place the product at room temperature before use
1 to 2 hours in the environment. Do not open the lid of the container before heating, so as not to affect the product performance.

2. The bonding surface should be kept dry and clean.

3. Evenly apply the adhesive to both sides of the material to be bonded. During the curing process of the adhesive, appropriate pressure can be applied to ensure that the surfaces of the adhesive can be attached to each other.

4. Heating and curing, 160×30 minutes.

5. After use, it should be covered in time and stored in the refrigerator at 5℃.

Packing size: 500g/ box



  FS-9103 thermal silicone

1. Product description

FS9103 thermal silica gel has both strong adhesion and thermal conductivity. It is a neutral silicone adhesive used for bonding and heat conduction between CPU and heat sink, thyristor intelligent control module and heat sink, high-power electrical module and heat sink.

Second, product characteristics

. Both bonding effect and good thermal conductivity.

Weather aging resistance, yellowing resistance, use will not fall off, will not produce gaps to reduce heat dissipation effect;

Excellent high and low temperature resistance, little change in performance in the range of -50~+250℃, can be used;

. Single component, easy to operate;

Third, product technical parameters

    Typical technical parameter

appearance

White paste

Specific gravity

1.75 to 1.95g/cm3

Linear shrinkage (%)

0.6

Hardness (Shore A)

40

Tensile strength

2.5 MPa

Shear strength

2.0 MPa

Elongation at break

150% or higher

Service temperature range

-50 ~ 250℃

Surface drying time (25℃,50% humidity)

≤20 min

Volume resistivity

Acuity 2.0 x 1014 Ω * CM

Dielectric constant

2.8 (1.2MHz)

Thermal conductivity (w/(m.k))

1.2

 

4. Methods of use

◆ Clean the surface: clean the surface of the coated material.

◆ Sizing: unscrew the cap of the hose, squeeze the glue to the cleaned surface, make it evenly distributed, and close the adhesive surface to fix it.

◆ Curing

Place the glued part in the air and let it cure naturally. The curing process is a curing process from the surface to the inside, within 24 hours the glue will be cured to a depth of 2 ~ 4mm, if the position is deep, especially in the part that is not easy to access the air, the curing time will be extended. If the temperature is low, the curing time will be extended.

5. Storage and expiration date

It belongs to non-dangerous goods, please store in a cool and dry place where the temperature is below 35℃, the validity period is 12 months at 25℃, and pay attention to sealing after use. If there is slight rubber on the surface due to poor sealing, it can be removed without affecting the use.

6. Packing specification: 5kg/ barrel, 15kg/ barrel

MESSAGE

LEAVE A MESSAGE