产品中心新网站资料
产品中心新网站资料

产品中心新网站资料

1700, 1900 epoxy resin potting adhesive

FS-1700A/B epoxy resin potting glue 【 Product features 】● This product is a special packaging glue……

Related
message
detail
content details

FS-1700A/B epoxy potting adhesive

【 Product Features 】

This product is a special packaging glue for digital tube, dot matrix Display, etc. (LED Display), low viscosity after mixing, good fluidity, easy to defoam, long service time, easy to operate;

Medium temperature curing, curing speed is fast;

Small settling rate after curing, good moisture resistance, good luster, adjustable hardness;

The cured material has uniform light transmission, excellent electrical characteristics, resistance to humidity and heat and atmospheric aging;

 

【 Appearance transitivity 】

Test item

Conditions and methods for determination

FS-1700A

FS-1700B

appearance

Visual inspection

Colorless transparent liquid

Colorless transparent liquid

Density g/cm3

25

1.0 ~ 1.1

1.0 ~ 1.1

Viscosity Pa.s

40

1.0 ~ 3.0

0.02 ~ 0.04

Shelf life

Ventilated and cool

12 months

12 months

【 Usage method 】

Mixing ratio: A: B = 100:50 (weight ratio) Mixing viscosity 25℃ : 800-900cps

Gel time: 50℃×1 hour

Minutes can be used: 25 x 45 minutes

Curing conditions: Mixed evenly at 50℃×0.5 hours, placed at room temperature for 2 hours.

The surface of the product needs to be kept dry and clean;

Agent A and agent B according to the weight ratio of 100:50 glue, and accurate weighing, please remember that the ratio is the weight ratio rather than the volume ratio, A, B after mixing should be fully stirred to avoid curing;

A and B are mixed and placed for 10 minutes, then placed in the oven at 50℃ for half an hour and can be removed

702A/B can be used with diffuser and color paste. The recommended dosage is: red paste PC-003 2-6 diffuser DF-090 2-5

 

【 Note 】

The main agent and curing agent of this product will start to react slowly after mixing, and the viscosity will gradually become higher, so be sure to use it within the usable time, so as not to use it due to too high viscosity.

When the prepared glue is not used for the time being or there is still surplus, please seal it immediately to avoid the phenomenon of surface moisture absorption and product quality;

Do not touch the skin or eyes, please wash the skin with detergent; In case of eye contact, rinse with clean water before seeking medical advice.

Before a large number of use, please try a small number of products to master the use of skills to avoid mistakes.

 

【 Post-curing characteristics 】

 Hardness Shore D 88-92 Volume resistance 25 Ohm-cm 1.2×1015

Surface resistance 25 Ohm 5.4×1014 Resistance voltage 25 Kv/mm 22-24

 Water absorption 100 for 1 hour ≤0.35 glass transition temperature 102 ℃

 Linear expansion coefficient Cm/cm/ 6.6×10-5

 

【 Storage 】

This product should be stored in A ventilated, cool and dry place. The shelf life of agent A is six months, and the shelf life of agent B is three months. After passing the test, it can continue to use;

                                            
FS-1900A/B light guide stick adhesive

【 Product Features 】

This product is light guide stick glue, low viscosity after mixing, good fluidity, easy to defoam, can be used for a long time, easy to operate;

Room temperature curing, moderate curing speed, mild reaction, uniform heat release;

Small settling rate after curing, good moisture resistance, good yellowing resistance, smooth surface after curing, high gloss, adjustable hardness;

The cured material has uniform spectrum, excellent electrical characteristics, resistance to humidity and heat and atmospheric aging;

【 Appearance transitivity 】
 

Test item

Conditions and methods for determination

FS-1800A

FS-1800B

appearance

Visual inspection

White liquid

Colorless transparent liquid

Density g/cm3

25

1.0 ~ 1.1

1.0 ~ 1.1

Viscosity Pa.s

40

1.0 ~ 3.0

0.02 ~ 0.04

Shelf life

Ventilated and cool

12 months

12 months

 

【 Usage method 】

Mixing ratio: A: B = 100:75 (weight ratio) Mixing viscosity 25℃ : 800-900cps

Gel time: 50℃×1 hour

Minutes can be used: 25 x 45 minutes

Curing conditions: mixed uniformly 24 x 12 hours can be released, 48 hours to reach hardness

The surface of the product needs to be kept dry and clean;

There will be A small amount of sediment in agent A, stir agent A for 5-10 minutes before use, stir well before use

Agent A and agent B according to the weight ratio of 100:75 glue, and accurate weighing, please remember that the ratio is the weight ratio rather than the volume ratio, A, B after mixing should be fully stirred to avoid curing;

A and B can be poked after mixing

 

【 Note 】

The main agent and curing agent of this product will start to react slowly after mixing, and the viscosity will gradually become higher, so be sure to use it within the usable time, so as not to use it due to too high viscosity.

When the prepared glue is not used for the time being or there is still surplus, please seal it immediately to avoid the phenomenon of surface moisture absorption and product quality;

Do not touch the skin or eyes, please wash the skin with detergent; In case of eye contact, rinse with clean water before seeking medical advice.

Before a large number of use, please try a small number of products to master the use of skills to avoid mistakes.

 

【 Post-curing characteristics 】

 Hardness Shore D 88-92 Volume resistance 25 Ohm-cm 1.2×1015

Surface resistance 25 Ohm 5.4×1014 Resistance voltage 25 Kv/mm 22-24

 Water absorption 100 for 1 hour ≤0.35 glass transition temperature 105 ℃

 Linear expansion coefficient Cm/cm/ 6.6×10-5

 

【 Storage 】

This product should be stored in A ventilated, cool and dry place, the shelf life of agent A is 12 months, the shelf life of agent B is 12 months, the expiration test is qualified, can continue to use;

 


MESSAGE

LEAVE A MESSAGE