产品中心新网站资料
产品中心新网站资料

产品中心新网站资料

Emergency repair

518 emergency repair agent Performance characteristics ☆ Fast curing speed; ☆ Low surface treatment……

Related
message
detail
content details

518 emergency repair
Performance characteristics
Fast curing speed;
Low surface treatment requirements, with oil, water construction;
High bonding strength with all kinds of metals.
Product use
High strength, good toughness, 5 minutes curing at room temperature. It is used when pipes, radiators, water tanks, and gear boxes leak due to cracks, perforations, and corrosion.
Usage method
1. Surface treatment: rough and clean the surface.
2. Preparation: According to the quality ratio A:B=2:1 or volume ratio A:B=2:1, mix the two components of A and B evenly, and use immediately.
3. Coating: Apply the mixed material to the part to be repaired and compacted so that it is fully infiltrated with the base material.
4. Curing: 20 ~ 25℃ curing 50min can be put into use, if the temperature is too low should be heated or extended curing time to cure.
 
Performance parameter

Physical and mechanical properties table

colour

Physical state

Density (g/cm3)

Compressive strength (kg/cm2)
GB/1041-79

Shear strength (kg/cm2)
GB/7124-86

Tensile strength (kg/cm2)
GB6329-86

Bending strength (kg/cm2)
GB1042-79

Hardness (Shore D)
ASTM-D-2556

grey

paste

1.37

1012

288

585

92

86

 

Curing characteristics table (test conditions: temperature 20 ~ 25℃, relative humidity 55)

Operational time limit
(min)

Available time

Need curing time before full load operation

Operating temperature
()

Withstand temperature
()


10

Room temperature 3h

8h

-60 to 150

150



Transport and storage
Sealed storage in a cool and dry place, shelf life of 2 years. Avoid inversion and bump during transportation, and transport according to non-dangerous goods.
Packing specification: Two components, 250g/ set, 16 sets/box.
 
 

 
528 oil level emergency repair agent
Performance characteristics
Fast curing speed;
Low surface treatment requirements, with oil, water construction;
High bonding strength with all kinds of metals.
Product use
Portable oil
Repair, mainly used for transformers, oil tanks, oil tanks, oil pipes, and other equipment oil leakage repair .
Usage method
1. Surface treatment: rough and clean the surface.
2. Preparation: According to the mass ratio A:B=1:1 or volume ratio A:B=1:1, mix the two components A and B evenly, and use immediately.
3. Coating: Apply the mixed material to the part to be repaired and compacted so that it is fully infiltrated with the base material.
4. Curing: 20 ~ 25℃ curing 20min can be put into use, if the temperature is too low should be heated or extended curing time to cure.
 
Performance parameter

Physical and mechanical properties table

colour

Physical state

Density (g/cm3)

Compressive strength (kg/cm2)
GB/1041-79

Shear strength (kg/cm2)
GB/7124-86

Tensile strength (kg/cm2)
GB6329-86

Bending strength (kg/cm2)
GB1042-79

Hardness (Shore D)
ASTM-D-2556

translucency

liquid

0.95

855

183

346

614

83

 

Curing characteristics table (test conditions: temperature 20 ~ 25℃, relative humidity 55)

Operational time limit
(min)

Curing time

Need curing time before full load operation

Operating temperature
()

Withstand temperature
()


5

20min

6h

-60 to 120

150



Transport and storage
Sealed storage in a cool and dry place, shelf life of 2 years. Avoid inversion and bump during transportation, and transport according to non-dangerous goods.
 
Package specification: Two-component, liquid, 85g/ group.

 
626 wet face tonic
Performance characteristics
Fast curing speed;
Low surface treatment requirements, can bring water construction;
High bonding strength with all kinds of metals.
Product use
It can be used on the surface of wet and low temperature parts, mainly for pipes, valves, pump shells, boxes, etc., in wet conditions
mending.
Usage method
1. Surface treatment: rough and clean the surface.
2. Preparation: According to the quality ratio A:B=6:1 or volume ratio A:B=3.5:1, the two components of A and B are mixed evenly and used immediately.
3. Coating: Apply the mixed material to the part to be repaired and compacted so that it is fully infiltrated with the base material.
4. Curing: 20 ~ 25℃ curing 50min can be put into use, if the temperature is too low should be heated or extended curing time to cure.
 
Performance parameter

Physical and mechanical properties table

colour

Physical state

Density (g/cm3)

Compressive strength (kg/cm2)
GB/1041-79

Shear strength (kg/cm2)
GB/7124-86

Tensile strength (kg/cm2)
GB6329-86

Bending strength (kg/cm2)
GB1042-79

Hardness (Shore D)
ASTM-D-2556

brown

paste

1.53

912

272

322

566

96

 

Curing characteristics table (test conditions: temperature 20 ~ 25℃, relative humidity 55)

Operational time limit
(min)

Available time

Need curing time before full load operation

Operating temperature
()

Withstand temperature
()


30

12h

12h

-60 to 150

160



Transport and storage
Sealed storage in a cool and dry place, shelf life of 2 years. Avoid inversion and bump during transportation, and transport according to non-dangerous goods.
 
Packing specification: Two components, 500g/ set 16 sets/box.


MESSAGE

LEAVE A MESSAGE