产品中心新网站资料
产品中心新网站资料

产品中心新网站资料

600 series cylindrical parts holding adhesive

600 series cylindrical parts adhesive brand: Seal God is used for the assembly of cylindrical non-thr……

Related
message
detail
content details

600 series cylindrical parts holding adhesive

Brand: Feng Shen


It is used for the assembly of cylindrical non-threaded fittings, filling the internal space between the parts and curing into a flexible adhesive layer to improve the strength of the fitting parts. It is used for the assembly and holding of cylindrical parts such as shaft sleeve, bearing, pin and pulley.

        Single component, solvent-free, room temperature curing. There are many varieties, which can meet the requirements of gap fit, over-fit and interference fit. Shock resistance, medium resistance, shock resistance, aging resistance, high life. Fill the fit gap, the force is uniform, and the active gap between the shaft and the shaft sleeve avoids micro-seismic wear, bite, distortion, etc., simplifies and reduces the assembly process, and improves the production efficiency.
        The fit tolerance is relaxed and lower surfaces can be selected. Helps bearings and bushings find calibration points to produce rigid assemblies. Prevent micro-vibration wear between metals and corrosion of metal fittings.
Commonly used: the bearing is installed on the bearing seat or shaft; Install the rotor, gear, sprocket and pulley on the shaft; Holding cylinder sleeve; Install engine bowl plug; Remove fixing screws or pins; Avoid deformation of tools or machines; Install the jig shaft sleeve; Restore worn machine tools.
 
1603 cylinder parts holding adhesive
Packing specifications: 50ml/ bottle, 120 bottles/box; 250ml/ bottle, 40 bottles/case
General purpose, low viscosity, good oil dissolving, suitable for slightly oily surface and inert surface, such as sleeve, bearing, small motor rotor shaft, bushing and other assembly.
 
1609 cylindrical parts holding adhesive
Packing specifications: 50ml/ bottle, 120 bottles/box; 250ml/ bottle, 40 bottles/case
General purpose, low viscosity, solid key/shaft, bearing, small motor shaft, bushing, repair hole/shaft wear or out-of-tolerance parts.
 
1620 cylindrical parts holding adhesive
Packing specifications: 50ml/ bottle, 120 bottles/box; 250ml/ bottle, 40 bottles/case
Temperature resistant (204) type. Viscosity, no flow. Used for intermittently working under the temperature of 150~204℃ hole-sleeve fitting, etc. Such as fixed valve sleeve, injection movement sleeve, valve sleeve, cylinder keyway, etc.
 
1638 cylindrical parts holding adhesive
Packing specifications: 50ml/ bottle, 120 bottles/box; 250ml/ bottle, 40 bottles/case
High viscosity, can be fixed with the gap of the shaft, hole, key, for dynamic load or periodic load, for the strength of the working conditions.
 
1648 cylindrical parts holding adhesive
Packing specifications: 50ml/ bottle, 120 bottles/box; 250ml/ bottle, 40 bottles/case

Low viscosity, fast curing, continuous working temperature up to 175, suitable for small clearance, high continuous working temperature, need to be fixed quickly occasions.
 
1660 cylindrical parts holding adhesive
Packing specification: 50ml/ PCS, 60 PCS/box; 250ml/ bottle, 30 bottles/case
High viscosity, paste, used to fill large gaps (below 0.5mm), with sleeve, keys, bearings and other cylindrical mating parts. Repair badly worn shafts, holes, keyways, bearings, bushings, etc.
 
1680 cylindrical parts holding adhesive
Packing specifications: 50ml/ bottle, 120 bottles/box; 250ml/ bottle, 40 bottles/case
Medium viscosity, suitable for gap fit or interference fit, can replace pressure fit, fixed casing, belt shaft, gear, rotor, etc., repair hole/shaft fit and out-of-tolerance parts, gap < 0.25mm fixed.
 
Main physical and mechanical properties

Product type number

appearance

Viscosity (mPa.s)

Fill gap (mm)

Cured shear strength (N/mm²)

Operating temperature
()

Initial/full stabilization time (25)

1603

Green liquid

100/200

< 0.13

22 or higher

-55 to +150

20m/24h

1609

Green liquid

100/200

< 0.13

P 19

-55 to +150

10m/24h

1620

Green slime

7000/9000

0.1 ~ 0.38

P 19

-55 to +204

30m/24h

1638

Green slime

2000/4000

0.1 ~ 0.38

22 or higher

-55 to +150

10m/24h

1648

Green slime

500/700

< 0.15

22 or higher

-55 to +150

10m/24h

1660

Silver plaster

paste

0.1 ~ 0.5

P 17

-55 to +150

10m/24h

1680

Green liquid

1000/1500

0.1 ~ 0.25

P 21

-55 to +150

10m/24h

Key points of use
l Used to clean oil-free surfaces.
l Hold it for 24 hours before it can be put into use.

MESSAGE

LEAVE A MESSAGE